哪位技术达人帮帮我刷自制

w287485186

哪位技术达人帮帮我刷自制  287485186

w287485186

===================================================
2012年11月4日星期日 20:36:33

J-Runner v0.2 Beta (283) Started


X-Consoles loyalty bonus - DEMON15OFF until 31st
Checking Files
Finished Checking Files
Version: 01

Flash Config: 0x00000000
Can not Continue
Version: 01

Flash Config: 0x00023010
Trinity
Reading Nand to C:\Documents and Settings\Administrator\桌面\J-Runner\output\nanddump1.bin
Reading Nand
Error: 250 reading block 15
Done!
in 6:35 min:sec

Reading Nand to C:\Documents and Settings\Administrator\桌面\J-Runner\output\nanddump2.bin
Initializing Nand..
Nand Initialization Finished
Reading Nand
Error: 250 reading block 15
Done!
in 6:35 min:sec

Comparing...
Bad Block ID @ 0x0015 [Offset: 0x56A00]
Bad Block ID  0015 Found @ 0x03FF [Offset: 0x107BE00]
Block ID 03FF [Offset: 0x107BE00] remapped to Block ID 0015 [Offset: 0x56A00]
Bad Blocks Remapped
Bad Block ID @ 0x0015 [Offset: 0x56A00]
Bad Block ID  0015 Found @ 0x03FF [Offset: 0x107BE00]
Block ID 03FF [Offset: 0x107BE00] remapped to Block ID 0015 [Offset: 0x56A00]
Bad Blocks Remapped
Nands are the same
* unpacking flash image, ....
ECC'ed - will unecc.
UnECC'ed
* found decrypted CD
* found XeLL binary, must be linked to 0x1c000000
* we found the following parts:
SMC: 3.1
CB_A: 9230
CB_B: 9230
CD (image): 9230
CD (decrypted): 9452
* checking required versions...
ok
* patching SMC...
Patching Trinity version 3.1 SMC at offset 0x13B3
* Replacing CD...

* XOR HACK NEEDED FOR CB 9230
* patching CB_B...
patchset for 9188 found, 4 patch(es)
* Applying XOR Hack to CB_B 9230
*** Re-encrypting CB_B with xor keystream
*** Fixing entrypoint
* Replacing CB_A 9230 with 9188
* encrypting CB...
* constructing new image...
* base size: 70000
* No separate recovery Xell available!
* Flash Layout:
0x0..0x1FF (0x200 bytes) Header
0x200..0xFFF (0xE00 bytes) Padding
0x1000..0x3FFF (0x3000 bytes) SMC
0x4000..0x7FFF (0x4000 bytes) Keyvault
0x8000..0x9ABF (0x1AC0 bytes) CB_A 9188
0x9AC0..0x114EF (0x7A30 bytes) CB_B 9188
0x114F0..0x174EF (0x6000 bytes) CD 9452
0x174F0..0xBFFFF (0xA8B10 bytes) Padding
0xC0000..0xFFFFF (0x40000 bytes) Xell (backup)
0x100000..0x13FFFF (0x40000 bytes) Xell (main)
* Encoding ECC...Done!
------------- Written into output\image_00000000.ecc

Arm Version: Version: 01
Flash Config: 0x00023010
Writing Nand
Done!
in 0:28 min:sec

我用J-Runner 读取nand,合成ecc,写入ecc我这算是成功了吗 还是没成功  

小狼052

成功了，可以焊接脉冲板。开机等待ecc出来了。