遗憾 尝试D9刻录失败...

wengang1984

用UltraISO把自用压盘（玩过全关，应该没问题也没有开忽略错误）战神一做了一个ISO。然后要打D9补丁，结果显示这个不是双层DISK...（这要怎么做ISO啊？）不死心，硬刻，用的是SONY的DVD +R DL，显示什么超刻，继续....最后写入错误....盘也废了。
错误报告如下：谁能亲自指导一下？
3:23:28    #17 Text 0 File DVDPlusDualLayer.cpp, Line 465
    L0 Data Zone Capacity set to 2080848 (1FC050h, 4064MB) -> OK, confirmed setting
   
3:23:28    #18 CDR -1205 File DVDPlusDualLayer.cpp, Line 490
    刻录层1
   
3:23:28    #19 Text 0 File DVDPlusDualLayer.cpp, Line 498
    Start writing layer 1 at address 0 (0h)
   
3:23:28    #20 Text 0 File Cdrdrv.cpp, Line 8230
    ---- DVD Structure: Physical Format Information (00h) ----
    Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
     Book Type: DVD+R DL (14), Part Version: 1
     Disc Size: 120 mm,    Maximum Rate: <not specified> (F h)
     Number of Layers: 2,   Track Path: Opposite Track Path (OTP),  Layer Type: recordable
     Linear Density:      0,293 um/bit,  Track Density:  0,74 um/track
     Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
     End Physical Sector Number of Data Area:    FCFFFF h
     End Sector Number in Layer 0:            22C050 h
     Data in Burst Cutting Area (BCA) does not exist
      Disc Application Code: 0 / 0 h
      Extended Information indicators: 0 h
      Disc Manufacturer ID: RICOHJPN
      Media type ID: D01
      Product revision number: 67
      Number of Physical format information bytes in use in ADIP up to byte 63: 64
     Media Specific [16..63]:
        00 00 00 52 49 43 4F 48 - 4A 50 4E 44 30 31 43 40   ...RICOHJPND01C@
        25 25 37 10 00 2C 6C 00 - 2C 6C 20 1F 0C 0C 14 14   %%7..,l.,l......
        02 01 01 20 00 20 1F 0C - 0C 14 14 02 01 01 20 00   ................
   
3:23:28    #21 Text 0 File dlgbrnst.cpp, Line 1713
    Set remaining time: 42:34,606 (2554606ms) -> OK
   
3:23:28    #22 Text 0 File DVDPlusRW.cpp, Line 628
    Start write address at LBA 0
    DVD high compatibility mode: Yes
   
3:24:17    #23 SCSI -1135 File Cdrdrv.cpp, Line 1445
    SCSI Exec, HA 0, TA 0, LUN 0, buffer 0x03D70000
    Status:    0x04 (0x01, SCSI_ERR)
    HA-Status  0x00 (0x00, OK)
    TA-Status  0x02 (0x01, SCSI_TASTATUS_CHKCOND)
    Sense Key:  0x03 (KEY_MEDIUM_ERROR)
    Sense Code: 0x0C
    Sense Qual: 0x00
    CDB Data:  0x2A 0x00 0x00 0x00 0x46 0x40 0x00 0x00 0x20 0x00 0x00 0x00
    Sense Data: 0x70 0x00 0x03 0x00 0x00 0x00 0x00 0x12
            0x00 0x00 0x00 0x00 0x0C 0x00
   
3:24:17    #24 CDR -1135 File Writer.cpp, Line 304
    写错误
   
3:24:17    #25 Text 0 File ThreadedTransfer.cpp, Line 229
    all writers idle, stopping conversion
   
3:24:17    #26 Text 0 File ThreadedTransfer.cpp, Line 223
    conversion idle, stopping reader
   
3:24:18    #27 Phase 127 File dlgbrnst.cpp, Line 1855
    正在生成DVD高兼容性边界
   
3:31:42    #28 SCSI -1135 File Cdrdrv.cpp, Line 1191
    SCSI Exec, HA 0, TA 0, LUN 0
    Status:    0x04 (0x01, SCSI_ERR)
    HA-Status  0x00 (0x00, OK)
    TA-Status  0x02 (0x01, SCSI_TASTATUS_CHKCOND)
    Sense Key:  0x03 (KEY_MEDIUM_ERROR)
    Sense Code: 0x0C
    Sense Qual: 0x00
    CDB Data:  0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
    Sense Data: 0x71 0x00 0x03 0x00 0x00 0x00 0x00 0x12
            0x00 0x00 0x00 0x00 0x0C 0x00
   
3:31:42    #29 Text 0 File dlgbrnst.cpp, Line 1713
    Set remaining time: 0:00,000 (0ms) -> OK
   
3:31:42    #30 Phase 129 File dlgbrnst.cpp, Line 1855
    已完成生成DVD边界
   
3:31:42    #31 Text 0 File dlgbrnst.cpp, Line 1713
    Set remaining time: 0:00,000 (0ms) -> OK
   
3:31:42    #32 Phase 38 File dlgbrnst.cpp, Line 1855
    以2.4x (3,324 KB/s)的速度刻录失败.

kakarote

不要用ultraiso，用dvddecrypter做镜像r，会出来一个iso文件及一个mds文件，直接忽略mds，给iso打d9补丁，再用dvddecrypter刻盘，OK，反正我是没改过什么booktype

gtrs

請愛用DVD Decrypter，想買單片的-R DL等不到，把手上僅有的一張+R DL拿去燒戰神2
打過DL補丁也是直接用DVD Decrypter燒，沒改Booktype，成功

强袭自由

刻PS2游戏推荐DVD Decrypter