在广大混刷大军热潮不减的时候送上点凉水吧，看看国外的哥们是怎么玩的吧

显示全部楼层 · 发表于 2011-7-26 23:17 · 日本

不知道还记不记得前阵子那个俄国的帖子，就是那个割电路做跳针解锁的那个，估计大家现在满脑袋都是混刷啊，套件什么的，我前阵子发的帖子也都不知道沉哪去了，这个就不说了，但是不知道看没看到这个帖子http://forums.xbox-scene.com/index.php?showtopic=733724这个是我在xbox-scene的论坛里找到的，也是回应不多的一个帖子，全英文的，一开始我也就当个热闹看，看看国外的哥们怎么发挥他们的热情，研究这些“不符合逻辑”的“无聊办法”但是越看我越吃惊，知道我看到这个家伙的发帖子，原文是这样的：
I'd just unlocked 2 slim 0225 today.

Mediatek MT1335WE 1020 CMSL
Mediatek MT1335WE 1021 BLSL（我的机器上的芯片就是这个型号的，嘿嘿，激动啊）

I thought all Mediatek were Winbond, and I almost sent they away, but the ower asked me to try, and for my surprise, they were MXIC.

I used a 10ohms resistor for them.

The 1021 BLSL kept the SPI unlocked after the unlock. The xbox's dashboard was 9199, I updated the dash to 12625 and the drive was restored to OFW. I had to flash it again with LT+ 1.9. Then I was curious about what would happen if I update to 13599. I updated the dash and the drive remained unlocked.
英语好的翻译一下吧，不过第一句我还是翻译过来了，今天我刚刚解锁了两个0225…………
他说的可是用俄罗斯的办法解锁的哦…………看来国外的哥们胆子不小，同时我也真正了解了一句话，撑死胆大的，饿死胆小的…………我打算这个周末也当把胆大的…………

显示全部楼层 · 发表于 2011-7-26 23:24 · 山东

哈哈，沙发。沙发

显示全部楼层 · 发表于 2011-7-26 23:26 · 山东

有个问题大家讨论一下啊。关于芯片烧死的问题。

芯片方面的知识不懂。不过听说烧死相当是保险丝熔断。芯片一旦烧死就不可逆转了。

永远的只能读不能写入了。问题是0225是烧死了还是无法解锁、

显示全部楼层 · 发表于 2011-7-26 23:33 · 云南

这个只有微软知道吧，我觉得应该不至于吧，厂商总会给自己留点余地吧。

显示全部楼层 · 发表于 2011-7-26 23:41 · 山东

微软一直在换光驱啊 9504、0225、0401、0272还有没见过的0500

显示全部楼层 · 发表于 2011-7-26 23:51 · 日本

看了一些国外网站还有国内高手的帖子，对于这个MT1335WE也有些了解了，首先说一下，这个有鉴于现在的电子芯片的结构构成，除了EEPROM之外其他的IC都没有烧死之说，至于具体到了0225这个光驱，那就要说其实只是设定了特定的SPI值当做密码而已，而前一阵子所的那个什么mxic啊Winbond啊，说的不是主板芯片，跟那个没关系，那个指的是MT1335we内部存储固件的存储芯片的类型，看国外的意思好像是9504的都是MXIC的，0225的都是Winbond的，但是我找到的这个帖子来看，好像有一部分0225的也是mxic的。（因为有人用这个方法吧0225光驱给解锁了……）至于怎么看主要是看芯片的序列号

显示全部楼层 · 发表于 2011-7-26 23:55 · 日本

OK
继续。
首相，我在这个帖子里发的那个，
Mediatek MT1335WE 1020 CMSL
Mediatek MT1335WE 1021 BLSL这个就是光驱的IC型号，你可以对一下你的芯片什么型号，我的就是这个1021 BLSL，而且很幸运这个型号的芯片是可以解锁的，当然除了9504的0225的光驱好像只有很少一部分是可以解锁的，我再找找看那个可以解锁啊
Winbond Mediatek MT1335WE - 1010 - BLSL didn't don't WORK

Winbond Mediatek MT1335WE - 1011 - BLSL WORKED - 10r resistor

Winbond Mediatek MT1335WE - 1014 - BLSL didn't don't WORK

Winbond Mediatek MT1335WE - 1016 - BLSL WORKED - 10r resistor

Winbond Mediatek MT1335WE - 1017 - BLSL didn't don't WORK
Winbond Mediatek MT1335WE - 1019 - BLSL didn't don't WORK
Winbond Mediatek MT1335WE - 1020 - BLSL didn't don't WORK
Winbond Mediatek MT1335WE - 1036 - BLSL didn't don't WORK
Winbond Mediatek MT1335WE - 1038 - CMSL didn't don't WORK
Winbond Mediatek MT1335WE - 1040 - BLSL didn't don't WORK
Winbond Mediatek MT1335WE - 1041 - CMSL didn't don't WORK
Winbond Mediatek MT1335WE - 1042 - CMSL didn't don't WORK
Winbond Mediatek MT1335WE - 1048 - BLSL didn't don't WORK
Winbond Mediatek MT1335WE - 1051 - BLSL didn't don't WORK

显示全部楼层 · 发表于 2011-7-26 23:59 · 山东

明白了。一直以为mxic、Winbond是主板的bios芯片品牌。

之前不解，为什么刷机还要特定的主板bios。现在这么解释豁然开朗。

tcgame · 发表于 2011-7-27 00:08 · 辽宁

支持一下！！还没工夫动手
x360-pro到手了。

显示全部楼层 · 发表于 2011-7-27 00:11 · 日本

看那个帖子上说的，现在的俄罗斯方法的可以吧所有是MXIC的，mt1335we解开，但是
Winbond的不可以，而0225的大所属都是Winbond的，只有少数型号的可以解开，这还是国外那些人一个个试验出来的，而Winbond的之所以解不开是因为一个电压值的原因，我的英语不太好，那些人还在接着俄罗斯的黑客的办法在研究呢，另外求一个英语超好的帮忙翻译一下这个

Hi!

It´s nice to see that finally this diy-solutions made its release.

Regarding the winbond issues:

1. Russian guys/sekil say you you need max. 1,0V DC at the Probe. Since its fed by VCC/CS you need to burn ~ 2,3 V DC.
Since the russian site did update the R Values for winbond to 3-5 ohms you must use at least a 2W resistor/trimpot to protect from burning.

A far better/more stable solution than twiddly resistors/trimpots is

1) a 1,0 V Zenerdiode (at least 1,3W) to ground or
2) two diodes in series i.e. 1n4007 (VF=0,7V) + BAt41-46 (VF=~ 0,3 V) and ground. Even 2 LED´s in series could/should work.

The benefit is: the diodes remain a high impedance at C59 (could be realy important)

2. Since winbond chips (read datasheet) need synchronisation to CLK (MXCI datasheet doesnt mention this), the winbond chips are usualy much more stable by design.

3. i came across a very skilled italian board (tech´s might already know it). they worked on winbond´s software and hardware protection for quite some time.

Since i read across somewhere: "you dont need that russian tool..." is bs. Since that tool is sending Status Register Protect (SRP) and BP instructions. So USE the Russian Tool and click the UNLOCK utton!

4. Since this kind of MRA-check is like the ProbeV1-3 in old LT´s you need the "phat" button in JF. Dont use the "slim" Button (this is also found in TX Tutorial).

Good luck,

snyder80

		自动登录	找回密码
密码			注册