- 精华
- 0
- 帖子
- 6793
- 威望
- 0 点
- 积分
- 6937 点
- 种子
- 593 点
- 注册时间
- 2012-5-29
- 最后登录
- 2024-12-23
|
楼主 |
发表于 2018-5-19 19:51 · 广西
|
显示全部楼层
本帖最后由 powerh3 于 2018-6-26 13:22 编辑
GroovyMame论坛一个国外玩家,把一个笔记本240p成功了,哈哈。。。
是AMD A8 APU ,整合了AMD Radeon HD 6620G核显。。。大家可以参考一下他的安装和设置过程。。。
http://forum.arcadecontrols.com/index.php/topic,152655.0.html
是在Win10下安装Catalyst 12.6成功的,而之前安装的驱动是Crimson 16.2.1 non-GCN* cards,有问题,该驱动认出的显卡是Radeon HD 7400M。
Ok, so I made another windows 10 clean installation this morning to install Calamity drivers properly, and I can confirm that the installation shows two MS Basic Display adapters, I suposse it's an APU thing. I chose the second one and the drivers installed fine.
Then I ran VMMaker, and followed the Calamity guide steps, with an exception, my graphics card has two outputs, hdmi and vga, so I thought I had to choose "Analog_0" because the card has 1 analog output, but it seems the laptop screen counts as another analog output and choosing Analog_0 doesn't work for me. I tried with Analog_1 and worked, but the laptop screen was still the primary in my case, I connected the tv and it showed the extended laptop, so I went into windows display configuration and chose to use only the second display, and followed the rest of the guide.
果然笔记本的输出240p成功关键和主副口和主副屏幕有关。这笔记本有HDMI和VGA两个输出接口,他选择模拟口Analog_0不成功(该玩友猜测笔记本自带屏幕是占用了模拟口Analog_0),而Analog_1口成功。然而笔记本的本身自带屏幕就是primary主屏幕,通过VGA口接到电视上显示的是扩展笔记本桌面(副屏幕),于是进入windows display configuration系统显示设置,只使用第二显示屏(关闭笔记本自带主屏幕,只使用VGA口输出到CRT电视或彩监的副屏幕)才行。
猜测:该玩家装驱动时出现了HD 7400M,我估计是他笔记本的独显(也可能是驱动和系统认错)。HD 7400M系列如HD 7470M,查TechPowerUp网,是40nm的非GCN卡,装Crimson 16.2.1 non-GCN*或Catalyst 12.6有机会成功,Crimson 16.2.1 GCN*则不对该显卡。。。
他的笔记本或许有两个显示核心,一个是APU的核显HD 6620G,32nm。一个是独显HD 7400M,40nm。可能笔记本的VGA头是对应核显HD 6620G的,而独显HD 7400M装完Crimson 16.2.1 non-GCN*依然无法输出模拟信号到VGA头,也许独显HD 7400M的模拟信号是输出到模拟口Analog_0上,而Analog_0被笔记本的自带屏幕占用了,即独显HD 7400M的模拟信号输出给了笔记本屏幕,而无法输出到VGA头(Analog_1口)了
所以只能用APU的核显HD 6620G通过VGA口(Analog_1口)输出低解240p模拟信号。
或许改改设置,能让独显HD 7400M也能通过VGA口输出模拟信号。
NoteBookCheck网站正好有这个笔记本双显卡介绍。
AMD Radeon HD 6620G + HD 7450M Dual Graphics
https://www.notebookcheck.net/AM ... aphics.73445.0.html
Then I generated the modelines, but when I tried to install them a error message appeared with each of them notifying that the modeline couldn't be installed because it was rejected by the driver, so I closed VMMaker and ran it again, this time as an administrator, and this time it worked fine.
生成低解分辨率的modelines时出错,关闭VMMaker再运行它,这次成功了。
The proof:
点击放大
|
|