速围观，最新关于0225的破解教程（英文版）

该用户已被禁言

一下该文均出自C4官网，小弟只是搬过来好方便大家用，英语达人翻一下吧     
Up to the date of this post there are three versions of the Liteon DG-16D4S, the 9504, the 0225 and the 0401. This guide covers the 0225. The stock 0225 PCB cannot be written to without some hardware hacks. This guide covers the Xecuter DG-16D4S Unlocked PCB which is a custom made replacement PCB that is a simply and easy swap with no soldering.

To find out which version of Liteon drive you have simply look at the label and you will see "FW Ver.: XXXX"

Here is an example of the Liteon DG-16D4S DVD label. As you can see we have highlighted the F/W version - in this case it is the 0225.



Before you connect everything you first need to install the X360USB Pro Drivers. These are signed and work in Windows XP / Vista / 7 both 32bit and 64bit. Download the small driverpack and plug in the X360USB PRO USB Cable. When it asks for the drivers simple point to the files you saved and they will install with ease. You are now ready to hook everything else up.

It's very easy to hook up your Liteon DG-16D4S to your PC. Simply connect the DVD power supply (in this case the Xecuter CK3 Pro) to the DVD drive (take care to make sure it is fitted the correct way - the wrong way can damage your drive) and to a molex power cable from your PC or from an external Molex power supply. Then connect the SATA cable from the DVD drive to the X360USB Pro, and then connect the USB cable from the X360USB Pro to a USB port on your Netbook/Notebook/Laptop/Desktop computer.

Remember that you need to be running at least v18 of the X360USB PRO firmware, and that needs to be flashed with at least v0.12 of the X360USB PRO Update Tool. If you don't the latest JF will not work with Slims.


OK we are ready to begin:

1. Load up Jungle Flasher and...

(1) Select the DVDKey 32 Tab
(2) Make sure the I/O Port is set to 0x000
(3) The X360USB PRO should be detected as Primary Master and the Firmware version will be displayed (in this case it is Ver 0.18)
(4) The Liteon DG-16D4S should be detected and ready to work with
(5) Make sure Dummy.bin is ticked
(6) Click on the SlimKey button


2. You will be asked if you want to send the unlock command to the drive. Click No.



3. Now click Yes and then power cycle the drive (Turn the CK3 Pro power off then on)


4. The drive will now kick into vendor mode (0x72)


5. Jungle Flasher will now perform a number of tricks to get the all important drive key.



6. You will be asked to save the Dummy file which contains the important data from your drive such as your drive key. DO NOT LOSE THIS FILE !



7. The following part of the guide is solely to show 3rd party tools working with the X360USB PRO. You must own any game that you backup and we do not condone any kind of piracy and this is purely for educational purposes only. We do not provide any of the LT Plus firmware files and they are not provided or included with Jungle Flasher so do not ask for them. Once the drives firmware has been read Jungle Flasher will ask you if you want to auto-load the Lite-On iXtreme firmware. Click Yes.



8. Everything is now loaded into Jungle Flasher and you are ready to go. lets explain whats happening on the screen at the moment.
(1) The source buffer is loaded with the Dummy.bin from your Liteon DG-16D4S drive. It shows here that it is an 0225 SlimKey extraction.
(2) This is your DVD key - always keep this safe !
(3) This is the iXtreme LT+ firmware auto loaded into the target buffer. This example shows the LT+ v1.9 0225 Firmware which is for the new 2.0.13146.0 dashboard update.



9. At this point you will unplug your DVD drive and now connect the Xecuter DG-16D4S Unlocked PCB (or your custom made PCB with the Pro Kit installed). You don't have to rig it up to your DVD drive chassis just yet - you can simply connect the PCB to the X360USB PRO and the CK3 Pro. Make sure that the power cable is the correct way around from the CK3 Pro and that the WP switch is set to "WP=1". Now you are ready to program the PCB.

(1) Select the MTK Flash 32 tab
(2) Click the I/O refresh button and make sure that the drive properties show that its a PLDS DG-16D4S
(3) Set the drive type to Phat (this is not a mistake)
(4) The PCB will detect as a Liteon Slim
(5) Click the Intro/Device ID button


10. You may need to power cycle if the drive doesn't kick into vendor mode on its first attempt. Most of the time it will kick straight in though.

(1) You are now in Vendor Mode
(2) The drive properties should be on display - everything is looking great !
(3) You will see a new button that says 0x00. This is the SPI Lock Status. 0x00 means it is unlocked and write protection is disabled.

Tip

If the PCB doesn't detect and you can't get into vendor mode with the above method and are stuck at 0x52 simply click Intro/Device ID and power cycle - you should then get into vendor mode (0x72) with no problems.




11. Now click on Write. As you can see the write / verify commands are sent very quickly with the X360USB PRO.
12. Now click on the SPI Lock Status button


13. The SPI Lock Status will now change to 0x8C. This means that the Write Protect is now enabled. Move the switch on the PCB to "WP=0"


14. You are now all done

(1) You can now click the Outro / ATA Reset button to take the drive out of vendor mode (With the 0225's you should hit this button a few times - this solves the "Open Tray Error")
(2) The drive properties show show that it is a PLDS DG-16D4S 0225


IDIOTS GUIDE TO USING THE FORUM: BEFORE POSTING HERE READ THE NOTICE AT THE TOP OF THE PAGE THAT SAYS "READ THIS BEFORE POSTING".

wangzpyoyo

真的假的啊？来个高人翻译下

该用户已被禁言

顶上去，别沉了，大家赶紧看吧，或许有用呢

我不会飞

的确是教程，不过需要套件

该用户已被禁言

哎，没套件。看来还得等啊，什么时候才有头啊

该用户已被禁言

小弟已将官网内容搬运过来，大家赶紧运用集体的智慧吧！

该用户已被禁言

原来网站多少。看下~~~

sashimizhao

我已经在另一个帖子里面翻译了

https://bbs.a9vg.com/thread-1975913-1-1.html

断下

图挂了吗？我看到红叉