我帮贴上来 0225英文教程 水平有限 有没有好心人翻译

jxgt

The following tutorial will take you through the simple process of reading a Liteon DG-16D4S DVD Drive (Firmware version 0225) and then installing the Xecuter DG-16D4S Unlocked PCB to that drive and writing new firmware using Jungle Flasher and an X360USB PRO adapter.

Requirements:

• Xecuter X360USB Pro
• DVD Drive Power source (the tutorial uses an Xecuter CK3 Pro - but of course you can use a CK3 Lite also)
• Xecuter DG-16D4S Unlocked PCB (you can also use the PCB that had the Pro Kit installed too)
• Sata Cable (Supplied with X360USB Pro)
• USB Cable (Supplied with X360USB Pro)
• Latest version of Jungle Flasher (Must be v0.1.85 beta and above - Not released just yet)
• Latest version of X360USB PRO firmware (must be at least v18)
• X360USB PRO Windows Drivers
• Windows XP / Vista / 7 - 32bit or 64bit
• MAC OSX (Using Parallels, Bootcamp or VMWare)
  

Warning
X360USB PRO AUX Power Cable

The X360USB PRO comes with an AUX Power cable (black cable with DC jack on one end and USB on the other). This is NOT to be used unless it is required. Your X360USB PRO will function with no problems on 99% of USB ports as they have a 500ma output. A tiny amount of USB ports only carry 100ma. The AUX Power is supplied as a worst case scenario for those instances (you would plug it into a USB capable power supply unit such as the iPod's power brick). DO NOT use the AUX Power cable if your computer supports 500ma as you may cause damage to your X360USB PRO. The best way to test is it just set everything up to see if drivers install, jungle flasher detects the drive etc.





Up to the date of this post there are three versions of the Liteon DG-16D4S, the 9504, the 0225 and the 0401. This guide covers the 0225. The stock 0225 PCB cannot be written to without some hardware hacks. This guide covers the Xecuter DG-16D4S Unlocked PCB which is a custom made replacement PCB that is a simply and easy swap with no soldering.

To find out which version of Liteon drive you have simply look at the label and you will see "FW Ver.: XXXX"

Here is an example of the Liteon DG-16D4S DVD label. As you can see we have highlighted the F/W version - in this case it is the 0225.



Before you connect everything you first need to install the X360USB Pro Drivers. These are signed and work in Windows XP / Vista / 7 both 32bit and 64bit. Download the small driverpack and plug in the X360USB PRO USB Cable. When it asks for the drivers simple point to the files you saved and they will install with ease. You are now ready to hook everything else up.

It's very easy to hook up your Liteon DG-16D4S to your PC. Simply connect the DVD power supply (in this case the Xecuter CK3 Pro) to the DVD drive (take care to make sure it is fitted the correct way - the wrong way can damage your drive) and to a molex power cable from your PC or from an external Molex power supply. Then connect the SATA cable from the DVD drive to the X360USB Pro, and then connect the USB cable from the X360USB Pro to a USB port on your Netbook/Notebook/Laptop/Desktop computer.

Remember that you need to be running at least v18 of the X360USB PRO firmware, and that needs to be flashed with at least v0.12 of the X360USB PRO Update Tool. If you don't the latest JF will not work with Slims.



OK we are ready to begin:

1. Load up Jungle Flasher and...

(1) Select the DVDKey 32 Tab
(2) Make sure the I/O Port is set to 0x000
(3) The X360USB PRO should be detected as Primary Master and the Firmware version will be displayed (in this case it is Ver 0.18)
(4) The Liteon DG-16D4S should be detected and ready to work with
(5) Make sure Dummy.bin is ticked
(6) Click on the SlimKey button



2. You will be asked if you want to send the unlock command to the drive. Click No.



3. Now click Yes and then power cycle the drive (Turn the CK3 Pro power off then on)



4. The drive will now kick into vendor mode (0x72)



5. Jungle Flasher will now perform a number of tricks to get the all important drive key.



6. You will be asked to save the Dummy file which contains the important data from your drive such as your drive key. DO NOT LOSE THIS FILE !



7. The following part of the guide is solely to show 3rd party tools working with the X360USB PRO. You must own any game that you backup and we do not condone any kind of piracy and this is purely for educational purposes only. We do not provide any of the LT Plus firmware files and they are not provided or included with Jungle Flasher so do not ask for them. Once the drives firmware has been read Jungle Flasher will ask you if you want to auto-load the Lite-On iXtreme firmware. Click Yes.


8. Everything is now loaded into Jungle Flasher and you are ready to go. lets explain whats happening on the screen at the moment.

(1) The source buffer is loaded with the Dummy.bin from your Liteon DG-16D4S drive. It shows here that it is an 0225 SlimKey extraction.
(2) This is your DVD key - always keep this safe !
(3) This is the iXtreme LT+ firmware auto loaded into the target buffer. This example shows the LT+ v1.9 0225 Firmware which is for the new 2.0.13146.0 dashboard update.


9. At this point you will unplug your DVD drive and now connect the Xecuter DG-16D4S Unlocked PCB (or your custom made PCB with the Pro Kit installed). You don't have to rig it up to your DVD drive chassis just yet - you can simply connect the PCB to the X360USB PRO and the CK3 Pro. Make sure that the power cable is the correct way around from the CK3 Pro and that the WP switch is set to "WP=1". Now you are ready to program the PCB.

(1) Select the MTK Flash 32 tab
(2) Click the I/O refresh button and make sure that the drive properties show that its a PLDS DG-16D4S
(3) Set the drive type to Phat (this is not a mistake)
(4) The PCB will detect as a Liteon Slim
(5) Click the Intro/Device ID button



10. You may need to power cycle if the drive doesn't kick into vendor mode on its first attempt. Most of the time it will kick straight in though.

(1) You are now in Vendor Mode
(2) The drive properties should be on display - everything is looking great !
(3) You will see a new button that says 0x00. This is the SPI Lock Status. 0x00 means it is unlocked and write protection is disabled.



Tip
If the PCB doesn't detect and you can't get into vendor mode with the above method and are stuck at 0x52 simply click Liteon Erase and power cycle - that should work fine.






11. Now click on Write. As you can see the write / verify commands are sent very quickly with the X360USB PRO.



12. Now click on the SPI Lock Status button



13. The SPI Lock Status will now change to 0x8C. This means that the Write Protect is now enabled. Move the switch on the PCB to "WP=0"



14. You are now all done

(1) You can now click the Outro / ATA Reset button to take the drive out of vendor mode (With the 0225's you should hit this button a few times - this solves the "Open Tray Error")
(2) The drive properties show show that it is a PLDS DG-16D4S 0225

theal

沙发 图片都挂了
字数你妹

sashimizhao

我来帮lz翻译一下, 希望可以帮助大家.




The following tutorial will take you through the simple process of reading a Liteon DG-16D4S DVD Drive (Firmware version 0225) and then installing the Xecuter DG-16D4S Unlocked PCB to that drive and writing new firmware

using Jungle Flasher and an X360USB PRO adapter.

这份教程是指导你简单的读取0225固件,然后用Xecuter的破解PCB版配合JF和X360 USBPRO去写入破解固件

Requirements: 需求

•Xecuter X360USB Pro X360USB PRO刷机套件
•DVD Drive Power source (the tutorial uses an Xecuter CK3 Pro - but of course you can use a CK3 Lite also) CK3PRO电源板
•Xecuter DG-16D4S Unlocked PCB (you can also use the PCB that had the Pro Kit installed too) 破解PCB版
•Sata Cable (Supplied with X360USB Pro) 串口线
•USB Cable (Supplied with X360USB Pro) USB线
•Latest version of Jungle Flasher (Must be v0.1.85 beta and above - Not released just yet) 最新版本的JF(目前版本0.1.85)
•Latest version of X360USB PRO firmware (must be at least v18) X360USB PRO固件 (必须高于V18)
•X360USB PRO Windows Drivers 驱动
•Windows XP / Vista / 7 - 32bit or 64bit
•MAC OSX (Using Parallels, Bootcamp or VMWare)

Warning
X360USB PRO AUX Power Cable (这段是说X360USB PRO刷机电源板的电压问题,不用翻译了)

The X360USB PRO comes with an AUX Power cable (black cable with DC jack on one end and USB on the other). This is NOT to be used unless it is required. Your X360USB PRO will function with no problems on 99% of USB ports as they have a 500ma output. A tiny amount of USB ports only carry 100ma. The AUX Power is supplied as a worst case scenario for those instances (you would plug it into a USB capable power supply unit such as the iPod'spower brick). DO NOT use the AUX Power cable if your computer supports 500ma as you may cause damage to your X360USB PRO. The best way to test is it just set everything up to see if drivers install, jungle flasher detects the drive etc.

Up to the date of this post there are three versions of the Liteon DG-16D4S, the 9504, the 0225 and the 0401. This guide covers the 0225. The stock 0225 PCB cannot be written to without some hardware hacks. This guide covers

the Xecuter DG-16D4S Unlocked PCB which is a custom made replacement PCB that is a simply and easy swap with no soldering.
截止到现在,这份说明可以指导2种固件就是DG-16D4S的 0225和0401. 这份说明特指0225. 因为0225的特性普通的刷写被锁定,所以必须使用破解PCB板. 这里就来说明如果更换PCB板子而不用焊接.

To find out which version of Liteon drive you have simply look at the label and you will see "FW Ver.: XXXX" 如果想要找到你的光驱固件版本可以看光驱上的贴纸.

Here is an example of the Liteon DG-16D4S DVD label. As you can see we have highlighted the F/W version - in this case it is the 0225.
下面就是一份DG-16D4S的贴纸样品,你可以看到高亮的固件号码,这是一份固件为0225的光驱.


Before you connect everything you first need to install the X360USB Pro Drivers. These are signed and work in Windows XP / Vista / 7 both 32bit and 64bit. Download the small driverpack and plug in the X360USB PRO USB Cable.
When it asks for the drivers simple point to the files you saved and they will install with ease. You are now ready to hook everything else up.
在连接任何设备之前,你需要安装X360USB PRO的驱动.可以在XP/VISTA/7的32/64位系统下工作.下载驱动包然后把X360USB PRO 插上. 正常安装驱动就可以.

It's very easy to hook up your Liteon DG-16D4S to your PC. Simply connect the DVD power supply (in this case the Xecuter CK3 Pro) to the DVD drive (take care to make sure it is fitted the correct way - the wrong way can damage your drive) and to a molex power cable from your PC or from an external Molex power supply. Then connect the SATA cable from the DVD drive to the X360USB Pro, and then connect the USB cable from the X360USB

Pro to a USB port on your Netbook/Notebook/Laptop/Desktop computer.
然后把光驱接到电脑上.把光驱电源连接上(也可以使用刷机电源板).(注意一定要把电源的方向搞清楚,如果电源插反了,肯定烧光驱).把串口线连接到X360USB PRO上,然后把USB线材连接到X360USB PRO和你电脑的USB接口上.

Remember that you need to be running at least v18 of the X360USB PRO firmware, and that needs to be flashed with at least v0.12 of the X360USB PRO Update Tool. If you don't the latest JF will not work with Slims.
记住你必须要有版本号高于v18的X360USB PRO的固件,而且X360USB PRO的软件版本号必须高于0.12. 如果不是的话,最高版本的JF是无法工作在slim上的.


OK we are ready to begin: 现在开始

1. Load up Jungle Flasher and... 启动JF软件

(1) Select the DVDKey 32 Tab 选择DVDKEY 32 标签
(2) Make sure the I/O Port is set to 0x000 光驱接口必须选择到0x000
(3) The X360USB PRO should be detected as Primary Master and the Firmware version will be displayed (in this case it is Ver 0.18) 这时候X360USB PRO就能检测到总线上的光驱和光驱固件号了,固件号显示在左下方.
(4) The Liteon DG-16D4S should be detected and ready to work with  这时候光驱就可以被检测到进行下一步刷写.
(5) Make sure Dummy.bin is ticked 保证Dummy.bin是正确的.
(6) Click on the SlimKey button 点击 SlimKey 按钮.



2. You will be asked if you want to send the unlock command to the drive. Click No. 这时候软件会询问是否解锁光驱,点击NO



3. Now click Yes and then power cycle the drive (Turn the CK3 Pro power off then on) 现在点击YES,然后用电源板关闭,再开启电源.



4. The drive will now kick into vendor mode (0x72) 这时候光驱会进入vendor模式 (代码0x72)



5. Jungle Flasher will now perform a number of tricks to get the all important drive key. JF现在就可以自动提取光驱的所有固件.



6. You will be asked to save the Dummy file which contains the important data from your drive such as your drive key. DO NOT LOSE THIS FILE ! 这时候询问是否保存Dummy文件,里面包含了KEY等关键信息 千万不能丢失这个文件!!



7. The following part of the guide is solely to show 3rd party tools working with the X360USB PRO. You must own any game that you backup and we do not condone any kind of piracy and this is purely for educational purposes

only. We do not provide any of the LT Plus firmware files and they are not provided or included with Jungle Flasher so do not ask for them. Once the drives firmware has been read Jungle Flasher will ask you if you want to auto-

load the Lite-On iXtreme firmware. Click Yes.
    上面的步骤是讲解其他第三方软件如何和X360USB PRO一起工作.你必须要一份D盘,同时我们声明散装光盘是我们永远无法接受的,这份教程只是学习参考受用. 当光驱固件被全部读取之后,JF会询问是否自动载入破解固件,选择YES



8. Everything is now loaded into Jungle Flasher and you are ready to go. lets explain whats happening on the screen at the moment. 这时候所有的固件都被载入到JF中了,这时来解释一下屏幕上显示的一切东西:

(1) The source buffer is loaded with the Dummy.bin from your Liteon DG-16D4S drive. It shows here that it is an 0225 SlimKey extraction. 目标缓存已经载入了Dummy.bin文件, 现在显示的是0225 SlimKey 提取.
(2) This is your DVD key - always keep this safe ! 这时你的DVDKEY,千万保存好!
(3) This is the iXtreme LT+ firmware auto loaded into the target buffer. This example shows the LT+ v1.9 0225 Firmware which is for the new 2.0.13146.0 dashboard update. 这时最新的LT+固件,已经被自动保存到软件的缓存中了.这份固件显示LT+固件已经对应最新的XBXO360系统版本 2.0.13146


9. At this point you will unplug your DVD drive and now connect the Xecuter DG-16D4S Unlocked PCB (or your custom made PCB with the Pro Kit installed). You don't have to rig it up to your DVD drive chassis just yet - you can simply connect the PCB to the X360USB PRO and the CK3 Pro. Make sure that the power cable is the correct way around from the CK3 Pro and that the WP switch is set to "WP=1". Now you are ready to program the PCB.
  下面你必须拔掉光驱,然后把破解PCB板准备好. 现在还不必把光驱彻底都安装上.你可以先把破解PCB链接到刷机电源板上.保证电源都连接好了. 如果刷机电源板上有WP切换,需要把WP切换到 WP=1. 你现在就可以刷固件到PCB板子上了.

(1) Select the MTK Flash 32 tab 选择 MTKFLASH 32标签
(2) Click the I/O refresh button and make sure that the drive  properties show that its a PLDS DG-16D4S 选择I/O接口.保证光驱显示为PLDS DG-16D4S
(3) Set the drive type to Phat (this is not a mistake) 把光驱设置为Phat模式 (这么设置就可以,不是误打)
(4) The PCB will detect as a Liteon Slim 这时候PCB板子就被识别为SLIM
(5) Click the Intro/Device ID button 点击 Intro/Device ID 按钮.



10. You may need to power cycle if the drive doesn't kick into vendor mode on its first attempt. Most of the time it will kick straight in though.
   如果光驱没有进入Vendor模式,现在用电源板关闭,再次开启电源, 大部分破解PCB板子会直接进入Vendor模式.

(1) You are now in Vendor Mode 现在以及你干进入了 Vendor 模式
(2) The drive properties should be on display - everything is looking great ! 现在光驱版本号也显示正常了,完事就绪!
(3) You will see a new button that says 0x00. This is the SPI Lock Status. 0x00 means it is unlocked and write protection is disabled. 你可以看到下面的显示写着0x00, 这是SPI锁定状态. 0x00的意思是已经解锁了,准备被写入.



Tip 提示
If the PCB doesn't detect and you can't get into vendor mode with the above method and are stuck at 0x52 simply click Liteon Erase and power cycle - that should work fine.
如果PCB板子没有被检测到,而且你无法进入Vendor模式.并且下面代码显示0x52, 你必须点击 Liteon Erase按钮,然后再次关闭/开启一次电源板的电源.就能工作了.





11. Now click on Write. As you can see the write / verify commands are sent very quickly with the X360USB PRO. 现在点击写入.你可以看到各种写入和验证命令行在下面滚动.



12. Now click on the SPI Lock Status button 现在点击 SPI LOCK STATUS 按钮.



13. The SPI Lock Status will now change to 0x8C. This means that the Write Protect is now enabled. Move the switch on the PCB to "WP=0"
这时候SPI LOCK STATUS的代码已经显示为0x8C, 意味着写入保护开启. 把PCB板子上的WP切换开关选择到 WP=0.



14. You are now all done  完毕!

(1) You can now click the Outro / ATA Reset button to take the drive out of vendor mode (With the 0225's you should hit this button a few times - this solves the "Open Tray Error")
你可以点击Outro/ ATA 重启按钮把光驱从 Vendor模式中恢复到正常模式 (如果是刷写0225光驱,可能你需要多点击几次这个按钮 -这个按钮可以解决一些错误,比如不能开启托盘)
(2) The drive properties show show that it is a PLDS DG-16D4S 0225  现在光驱信息显示为 PLDS DG-16D4S 0225.

jxgt

感谢楼上的

kirin_vega

感谢楼主翻译，不过这个过程必须要用X360USB PRO刷机套件吗？用PCB板可以理解，换芯片，加写保护，可不可以用一般的刷机套件啊？

sashimizhao

我理解普通刷机版就可以. 你看TB上很多刷机版都写着支持SLIM

kirin_vega

那倒是可以入一个试试看了，有没有第一个吃完螃蟹的兄弟啊？

kirin_vega

看错了哈哈，感谢6楼的。

jxgt

现在混刷9504 比较捷径

jxgt

图可算修正了