- 精华
- 0
- 帖子
- 89
- 威望
- 0 点
- 积分
- 95 点
- 种子
- 5 点
- 注册时间
- 2008-12-13
- 最后登录
- 2016-7-1
|
楼主 |
发表于 2008-12-23 17:32 · 江苏
|
显示全部楼层
Instructions on flashing a LiteOn with JungleFlasher are as follows:
1: Hookup LiteON to sata port and power drive
2: In JungleFlasher select MTK Flash 32 Tab.
3: Select correct port (see above tutorials for figuring out the correct port)
4: Hit Lite-On-Erase button. NOTE - This is done AFTER you have already successfully transferred your inquiry.bin / identify.bin / key.bin files!!! Please read the Prompts VERY carefully! It is important to power cycle the drive at the correct moment to prevent your computer from freezing with VIA cards.
5: After power cycle, drive should return status 0x72 and display Flash information. If it does not, click Device ID and power cycle as prompted. If still not successful then you did not successfully erase the drive.
6: Once Flash information is displayed, you are ready to write! Go to firmware tool 32 tab and select "Load from dump files" and select your key/inquiry/identify .bin files. Then select ix15-liteon.bin after pressing "Open Target Firmware". Press "Spoof Source To Target". Then "Save to File" and save your CFW.bin.
7: Go back to MTK Flash 32 tab and select Write. It should automatically take the liteon firmware you loaded in the Firmware 32 tab and flash to the drive. It will automatically verify flash. If verified your done :)
If write verification fails, then there is likely a issue with JungleFlasher and your sata chipset. Please use DosFlash to flash the drive with the CFW.bin with the correct spoofed information. If the drive is successfully erased, dosflash will see the flash information and will be capable of writing!
这个不就是教程吗
1：联接建兴到SATA端口和电源驱动器
2 ：在JungleFlasher选择MTK闪光32标签。
3 ：选择正确的端口（见上文教程找出正确的端口）
4 ：选中建兴擦除按钮。注意-这是你已经成功地转移您的inquiry.bin/ identify.bin/ k ey.bin档案以后！请非常认真的阅读提示！重要的是，电源周期的驱动器在正确的时刻，以防止您的计算机不受冻结与威盛卡。
5 ：在电源周期，驱动器应返回状态0x72和显示Flash的信息。如果没有，点击设备ID和电源周期的提示。如果仍然没有成功，你没有成功地消除驱动器。
6 ：一旦闪光的资料显示，您已经准备好写！转到固件工具32标签并选择“加载从转储文件”并选择您的钥匙/调查/确定。彬档案。然后选择ix15 - liteon.bin后，按下“打开固件目标” 。按下“欺骗性源为目标” 。然后“保存到文件”并保存您的CFW.bin 。
7 ：回到MTK闪光32标签并选择收件。它应自动采取建兴固件你载入固件32标签和闪存的驱动器。它会自动验证闪存。验证您的操作： ）
如果写验证失败，那么就可能是问题JungleFlasher和你的SATA芯片组。请使用DosFlash闪存驱动器与CFW.bin与正确的欺骗性的信息。如果驱动器已成功清除， dosflash会看到闪光的信息和将能写！ |
|
川公网安备 51019002005286号
发表于 2008-12-23 17:31 · 北京
