A9VG电玩部落论坛

 找回密码
 注册
搜索
查看: 11071|回复: 38

xenon也可以脉冲自制了

[复制链接]

精华
0
帖子
197
威望
0 点
积分
210 点
种子
0 点
注册时间
2012-3-8
最后登录
2015-1-3
 楼主| 发表于 2012-3-8 03:52  ·  加拿大 | 显示全部楼层 |阅读模式
TX放出消息了,具体可以看官网,我等级低,发不了链接,TX大名鼎鼎,官网你不会不知道吧

We are happy to finally release the Xenon RGH Hack. This is by no means meant to be used for an everyday RGH as its as bad if not worse than a Zephyr, however it does work and will be perfect for those who have a Xenon where they lost their DVD key or an unbanned key vault.

Here is the readme included with the release:

Wiring

Generate your ecc image using the latest version of J-Runner and flash to your NAND (+w16 just like a regular RGH).

Program your TX CoolRunner (or whatever flavor RGH mod you are using) with the tx-xenon.xsvf or tx-xenon.jed file.

The Xenon has a capacitor on CPU_RST that was removed in later models.  C7R112 (located near the xclamp under the CPU) must be de-soldered, and the CPU_RST wire from the TX CoolRunner(D) must be soldered to the left pad (non grounded pad).

A 47nf ( 0.047uf) capacitor needs to be added between PLL_BYPASS(+) and GND(-).  (If you have a genuine TX CoolRunner REV B you can use the on-board by bridging the CAP jumper)

A 220-270pf capacitor should be added between CPU_RST(+) and GND(-) on the cpld. (If you have a genuine TX CoolRunner REV B this is already included in the design so not required)

An easy to follow picture guide can be found here:
Troubleshooting

Using a TX CoolRunner Rev B, and after applying various troubleshooting measures we have had glitches ranging from instant to 20 minutes.

The debug LED should flash on for less than a second and repeat every 5 seconds.  If your LED stays on or does not come on at all, it is usually because of something being wrong with PLL_BYPASS.  Try different values of capacitors and wires. If you have enabled the CAP on REV B of the TX CoolRunner, simply un-bridge it and try a 47nF cap instead as per the instructions above.

If it still has not glitched after several hours, try different values of capacitors on CPU_RST of your RGH mod.  A longer wire / low-loss 50 ohm double shielded cable may also help with this.

To help increase boot times and stability (on all RGH installs not just Xenon) we recommend that you try Low-Loss Double Shielded 50 ohm cable. It's very cheap to use and quite effective – so a quick shout out  who supplied a batch of high quality cable for our development team to use. It's less than 75 cents a foot – not bad.

NOTE: Remember when programming the TX CoolRunner that the Xbox power is NOT connected and that the switch is set to PRG before you connect the JTAG cable. If you connect the JTAG cable and it is set to NOR with the Xbox power connected, it can damage your NAND-X and/or CoolRunner. When you have finished programming, switch it back to NOR and then power on the Xbox.

The Xenon Hack

Please note that this hack is not available on consoles updated to dashboards 14717 or 14719.

If you are seeing the debug led it means that the cpu is probably not crashing and the issue addressed by gligli/tiros has been fixed (This can of course be a false positive as sometimes the CPU could be crashing but the SMC restarts fine – we can never be 100% sure)

So far, this is really only useful for a one time cpu_key dump. There will undoubtedly be ways of optimizing this hack in the future and who knows, it may become a reliable glitch one day.

We would appreciate that you give as much feedback to our support forums as possible to help others achieve better results and to improve this method. For now we can leave this and go back to RGH2.0 for Zephyr, Falcon, Jasper and also of course, the Corona.
这一段简单翻译:TX现在可以不用管xenon了,继续研究RGH2.0的肥机破解,当然还有corona,就是9.6A瘦机

Enjoy!

Xbox 360 Xenon RGH Hack brought to you by the Xecuter RGH Development Team


Thanks

Thanks are extended to Tiros & Gligli, without your work none of this would have been possible.

A special thanks goes out to cOz – your work on Dashlaunch proved to be an invaluable contribution and we look froward to your next exciting project.

Greets: Team Jungle, Team FSD, Freeboot, Libxenon & RGLoader.





精华
0
帖子
767
威望
0 点
积分
758 点
种子
5 点
注册时间
2006-11-5
最后登录
2019-4-26
发表于 2012-3-11 00:25  ·  山东 | 显示全部楼层
穿越回来抢个沙发,另外目前还没看到a9有刷成功的,毕竟双90少了,虽然我的xenon机从06年一直玩到现在

精华
0
帖子
376
威望
0 点
积分
430 点
种子
7 点
注册时间
2005-11-20
最后登录
2017-7-3
发表于 2012-3-11 01:42  ·  上海 | 显示全部楼层
难道说我的90后有救了

精华
0
帖子
50
威望
0 点
积分
52 点
种子
0 点
注册时间
2012-3-3
最后登录
2012-8-19
发表于 2012-3-11 08:13  ·  广东 | 显示全部楼层
这是不是说9.6A也可以破解了?

精华
0
帖子
289
威望
0 点
积分
330 点
种子
5 点
注册时间
2004-11-27
最后登录
2017-6-9
发表于 2012-3-11 09:11  ·  吉林 | 显示全部楼层
求高手写一篇简单翻译教程,造福大家

精华
0
帖子
43
威望
0 点
积分
526 点
种子
730 点
注册时间
2009-9-6
最后登录
2024-5-29
发表于 2012-3-11 11:36  ·  上海 | 显示全部楼层
对于老双90来说,这无疑是个好消息

精华
0
帖子
1562
威望
0 点
积分
2257 点
种子
1142 点
注册时间
2004-7-21
最后登录
2024-9-30
发表于 2012-3-11 12:12  ·  广东 | 显示全部楼层
我的就是双90,求教程。

精华
0
帖子
363
威望
0 点
积分
395 点
种子
5 点
注册时间
2005-8-14
最后登录
2024-9-23
发表于 2012-3-11 19:13  ·  江苏 来自手机 | 显示全部楼层
同求教程!!!!!

精华
0
帖子
767
威望
0 点
积分
758 点
种子
5 点
注册时间
2006-11-5
最后登录
2019-4-26
发表于 2012-3-11 21:18  ·  山东 | 显示全部楼层
ayatoayane 发表于 2012-3-11 01:42
难道说我的90后有救了

有救了,就等高人们的教程了

骑士

上午咖啡下午茶

精华
0
帖子
1564
威望
0 点
积分
2128 点
种子
7 点
注册时间
2007-8-25
最后登录
2024-8-27
发表于 2012-3-11 21:32  ·  北京 | 显示全部楼层
我那台06年的机子 可以拿出来了
您需要登录后才可以回帖 登录 | 注册

本版积分规则

Archiver|手机版|A9VG电玩部落 川公网安备 51019002005286号

GMT+8, 2024-10-1 06:15 , Processed in 0.205035 second(s), 18 queries , Redis On.

Powered by Discuz! X3.4

Copyright © 2001-2020, Tencent Cloud.

返回顶部