白板冷启动不行，已经有修改成功的朋友了,本人自己SLIM 法解决了

x-8232

最新，已经有人 试过这两种方法了 都有效果的，期待有更多的同样捆饶的朋友能成功，同样感谢那个老外REOLIN ，还有另外个老外提供跳线SLIM 的，以及看过此贴，先实验的朋友，  另外修改有风险，改前三思，后果自付 联动下 次贴成功的朋友https://bbs.a9vg.com/thread-2096088-1-1.html  本人今天重新购买了锡 ， 冷开成功， 另外种方法看图 就行了。。。




我发现白板，至少在我的6750 ，360 上 原来插着电源 第2天也是能开的，不插电的话大概1小时后就开不了了，要几次后反复关，是几次，不是2次，本来想换电容试，手头没，又听论坛哪贴里说白板这问题无解， 本来死心了，就那样玩吧， 但看到了一贴 http://forums.xbox-scene.com/index.php?showtopic=738658  不要***的应该，看到这老外FIX 了，但也没连线实际图，有谁解释下他说的可行不？3.3 V 不要接也行？  下面那张是U52B 的点的图 ，老外自己在 XBOXHACKER 上说，有同样问题的中国白版的使用者， 用同样方法解决了，     另外有意思的是那里回贴的某同志，说把白板的短接点跳线，跳在 SLIM 那，他的冷起毛病就没有了。。。。。。 看到别的方法继续更新吧。
下面是老外REOLIN的话。。。引用下
From factory, white chips have pin 7 and 15 shorted - there is 1.35v (diodes are used to lower 3.3v to 1.35v or near it).
It's not the right thing to have 1.35v on both pins - you should have 1.8v on pin 15 and 1.1v on pin 7.
So I decided to fix it - I took 1.8 straight from the xbox board (U5B2 on my falcon) and connected it to the "-"  of the middle diode (red square)(yes, it's "-", not "+" as it's printed on the board). Then I soldered the wire from the yellow square (1.8v) to pin 15 (lift this pin up - it should not be shorted with pin 7). If you do so, you will get ~1.2v on pin 7 (the third diode lowers 1.8v to 1.2v or so).
Don't connect 3.3v after this mod - the board can work without 3.3vStanby - you can read the "Cheap mod" thread on rgloader forums.
Also, reheat all components on the glitch board - cold solder can cause problems too.

Quote
Did i miss something here?? Ive read over his post several times and never once saw where he said he used that cpld. So which leads me to think that may not be his problem. Now if he IS infact using this cpld then you just got extremly lucky with you post.
Well, you can see "X360Glitch" in the title of that topic - the official name of those crappy white chineese chips. And the diagram is also for white board, so it's pretty strange you missed it

After all, I can't guarantee that my method will fix your problem, but you should definitely try. I posted it on other forums and several people fixed their problems after doing it.

是我了

白板好启动啊，我刷的双65用白板的基本秒启动

x-8232

是我了 发表于 2011-12-17 11:38
白板好启动啊，我刷的双65用白板的基本秒启动

不插电 ，第2天也能秒启动？

hitomilee

根据每个机器的体制有关吧，目前主要测试冷启动时间，如果冷启动也很快，那说明真的快了
我也好奇那个修复，不知道哪个机友试试看？

是我了

是的都秒启....................

x-8232

是我了 发表于 2011-12-17 12:02
是的都秒启....................

老大你改白板没处理什么吧？双65 。。除了  F 点加电容？

fatyme

机器体质问题
也是RP问题

x-8232

体制是有影响的吧， 但白板冷起不能也不是我一个， 等高手解决了。。。

368131152

原来白板必须预热20分钟才能起动冷机下，现在COOLRUNNER各种秒开，最快4秒多，偶尔50秒，没有超过1分钟的，赞一个。顺便说一下，白板必须预热在某些机器上

.asuka.

白色的，每次开机都要预热5分钟，然后关机，开机秒进！
Slim的搞过几台，都是冷机开机2多钟才能启动。~~实在蛋疼呀
这个可以期待下！