CR3 Lite/coolrunner v3 lite 焊接图 使用教材

奥莱电玩

The CR3 Lite comes with an adhesive foam pad and the positioning in pictures below. We changed the security sticker as so many cheap knock offs were ripping off our design. It fits nicely to the 360 faceplate now if you wish

We also used a high quality 48Mhz crystal - once the cheap knock offs hit the market you can be sure they will use the cheap ones which will be very poor performance.




Here are the default settings for the LK Solder Jumpers. As past experience by thousands of users has shown, you should try different settings for your setup until you achieve the best performance. It always helps others to post your own personal results.

Phat (Non-Jasper)

LK1 - Short (Disable Crystal)
LK2 - Open (Enable 10 Ohm on CPU_RST)
LK3 - Short (C15 Enable)
LK4 - All Open (Slim Settings)

Phat (Jasper)

LK1 - Short (Disable Crystal)
LK2 - Short (Disable 10 Ohm on CPU_RST)
LK3 - Short (C15 Enable)
LK4 - All Open (Slim Settings)

Slim (Trinity)

LK1 - Short (Disable Crystal)
LK2 - Short (Disable 10 Ohm on CPU_RST)
LK3 - Open (C15 Disable)
LK4 - Short 1-2 (300pF on CPU_RST to GND)
or
LK4 - All Open

Slim (Corona)

LK1 - Open (Enable Crystal)
LK2 - Short (Disable 10 Ohm on CPU_RST)
LK3 - Open (C15 Disable)
LK4 - Short 1-2 (300pF on CPU_RST to GND)
or
LK4 - Short 2-3 (100pF on CPU_RST to GND)
or
LK4 - All Open

The following CPU RESET CLEANER settings were taken from many users experiences and we compiled all the best settings into one easy board. If you want to read through some source material for these settings we suggest you goto this thread so you can see lots of feedback.

CPU RESET CLEANER (S2 DIP SWITCH)
To disable set 1 and 5 On and the rest OFF
You can use a mixture of 234 and 678. 1 and 5 must be set to OFF when using a combo.

(1) Bypass
(2) 1K ohm
(3) 2K ohm
(4) 3.3K ohm
(5) Bypass
(6) 470 pf
(7) 560 pf
(8) 680 pf

PLL_BYPASS CLEANER (S4 DIP SWITCH)

100nF has always proven great for Jaspers. I personally have success with 680pF. Others have reported their own better results with all the other values.

(1) N/A
(2) 680 pf
(3) 150 nf
(4) 100 nf (Default - Same as CAP solder Jumper on Rev C)
(5) 68 nf
(6) 47 nf

The wire install and setup is the same as the CoolRunner Rev C.

DemoN can now directly connect using the ribbon cable that is included with the DemoN (Programming and Enable/Disable feature)

ROL can be wired directly to one of the front LED's without any diode as its included on the CR3 as per this thread

Jasper




Trinity



Corona - Update: If you are installing to a Corona the yellow wire in the slim pack is too short - use the yellow wire in the phat pack.


YOU SHOULD ALWAYS REVERT TO STOCK FW BEFORE ANY MAJOR UPDATE - ALWAYS, ALWAYS, ALWAYS !!

BEFORE POSTING HERE READ THE NOTICE AT THE TOP OF THE PAGE THAT SAYS "READ THIS BEFORE POSTING".

该用户已被禁言

什么时候出 对4G效果好吗

该用户已被禁言

就是把所有东西就集成到板子上了

奥莱电玩

lsh1590 发表于 2012-9-23 16:30
什么时候出 对4G效果好吗

下周吧，这块板子集结 晶振 电阻电容(多个电容，有开关，可以方便自己调试主机，从而达到秒开），可以说是脉冲板的豪华版，奢侈品，呵呵

yhx861008

从做工看 真是奢侈品  该做的都做了 全部集成 高科技产品 能把9.6A秒开就给力了

黑金

奥莱电玩 发表于 2012-9-23 20:10
下周吧，这块板子集结 晶振 电阻电容(多个电容，有开关，可以方便自己调试主机，从而达到秒开），可以说是 ...

今天淘宝旺旺问你都不带回话的

yangjin237

这玩意得在80块钱以上啊.

奥莱电玩

黑金 发表于 2012-9-23 21:32
今天淘宝旺旺问你都不带回话的

你联系几号的，我去惩罚他，呵呵

奥莱电玩

yangjin237 发表于 2012-9-24 13:30
这玩意得在80块钱以上啊.

应该是100多以上了，

dbluep

看不太懂，貌似好东西