新薄機 Corona V4 VadimKR法取得DVDKEY !

小john

Hack of  Corona V4  VadimKR 法

(實際上是corona V3,  但是因為nand不是4G, 而是  250G /NAND  16MB,  CORONA第4片主機板 )
目前已經可以刷入XELL 取得CPU-KEY/DVDKEY , 而後呢...您可做什麼? 自行想像...當然,2.0.15574 的機板, 還不能刷入FreeBoot!!

確認是CORONA V3 , 但是記憶體晶片又不一樣了  !比較一下, 左邊是CORONA V3 , 右邊是CORONA V2 ..

找到板上的 R2C6 , R2C7 , R2C10 必須要短路!!, 不然 flashconfig 值會是]0x00000000

這塊機板沒有偵錯點(DEBUG POINTS),當然包含了post_out  [一般對接的脈衝藍板(Matrix) B點,TX白板的C點 ]!!
B點 連接至 post_out 必須焊到CPU 的鍚球上, 不必拆CPU , 用最細的線, 用放大鏡即可找到...
(至於要怎麼才能接鍚球接得成功漂亮, 嘿... 嘿... 山人自有辦法! 屬技巧問題,賣個關子)

注意, 本法屬高難度... 一般人要做好較難, 若沒成功需要重做BGA 植球回焊!!
目前能做的就是取得 2.0.15574 主機的dvdkey , 置入 X360key電子狗, 後變成硬碟直讀的機子,或是軟改LT3.0
至於要自製? 由於nand無法刷機 freeboot ,無解 ?! (ps .也許有神人可以解)
其實本機大概都是 2012/7/10 日之後出來的機子...  是否遇得到2.0.14719版的可以改自製,得碰運氣啦...



In the last article about the RGH v3, I mentioned consoles Corona, not amenable to hacking. Call them Corona v4. About them there is mention of the Internet, but there were no reports of successful attempt to crack. Now, I have something to tell you.
The new Xbox 360 motherboard version was hacked!

To begin with, how can they tell? So far, I reported only 250 Gb versions of these boxes, and they had one feature - no solder resistors near Reading NAND. In this case, it is not a simple Corona v3, as on the board, is the size of 16 MB of standard memory. UPD: Team Xecuter wrote that it Corona v3, but with a different memory. In this version some resistors were removed to prevent NAND dumping:

You can look for yourself. On the left - Corona v4, right - the usual prefix
At the left you can see the new corona MB, at the right - the older one

So, read this attachment, you must close the R2C6, R2C7 and R2C10 (otherwise, the Flashconfig 0 × 000000000)

To read it you can just shortcut them.It turned out that this is not the only difference between this version of the console! Point post_out (or point C on Coolrunner), the location of which can be seen in the picture, more leads nowhere!This MB version also has no debug points (including post_out) And, as without this point, Reset Glitch Hack does not work, have to find it. Consider, where she led?

point was connected to this CPU ball:

Yeah, it is, now, you need to solder directly to the terminal processor! So, it is clear that Microsoft is seriously concerned about the safety of their consoles? Yes, yes! RGH now put on such consoles will only professionals, because not everyone possesses the skills rebolla.To do the RGH you need to solder wire directly to this ball! It's Possible without removing the CPU.By the way, my friend nick VadimKR and found this, and successfully read the key processor with an attachment, for which he had the honor and praise :) Nothing is impossible, it's only in the complexity of execution!This Method was found and Implemented by VadimKR . And this photo of alex706 , he soldered without removal of the processor:Photo at this you CAN See the soldered (without removing the CPU) post_out wire by alex706 :
Be warned - the skills rebolla still have necessarily in an unsuccessful attempt to have to solder the processor.
Warning! If you damage the CPU balls, you must resolder it so be accurate.

小C、

纳尼  我是沙发吗  小白表示压力很大

该用户已被禁言

看不懂啊 似乎很困难的样子

小狼052

楼主是香港的一个马甲党。。既无图片也无详细说明。而且007的帖子都已经详细说明如何刷自制了。不知道楼主的意思何在还是翻译的不好。。

该用户已被禁言

至於要怎麼才能接鍚球接得成功漂亮, 嘿... 嘿... 山人自有辦法! 屬技巧問題,賣個關子)  这有什么关子的，用放大镜加焊台加热拉，自动会连上的

小john

是轉載給分給大家看一下和研究一下啦~而圖片我不懂怎轉載在這喔

小狼052

好在我看到图了。现在我的方法就是用U型针。。。。。

小john

哈~我也想貼圖出來~就是攪不到怎貼~說什麼容量過大~暈= =
小狼大大你說007貼過的可以給一下連結我嗎?我還在研究中

工作中

就是狼版和007***明的方法吧?

mirnamire

好像我一个月之前就转发过这个方法了……