[hack] 破解ps3读取iso工具极速放出[4.70 MB]下载始动

kaka1

欧洲首发，黑客hacked2123 兑现发布引导程序的承诺？

Summary:

Very simply I had a .h264 encoded video file, and encapsulated
it through VLC with M2TS, and transferred it to the PS3; it
claims the file is "Corrupted Data". When selected the PS3
prompts the screen with "The data is corrupted."

Here's the good part, that same file, when selected after
entering a game (any game), will produce a completely black
screen, no info, no beep, no nothing and the controller circle
and other buttons won't work. (PS button works, but when the
system is turned off it sounds like its yelling @ you (the
beeps))

-hacked2123


Usage (tested on v1.10):

To use this, put the included "libmpeg.mpg" file in a /VIDEO
folder of your Jumpdrive or similar storage device.

Turn on the PS3, then go to Video, select your Jumpdrive, and
select the "Unsupported Data" file and launch it by pressing X.

If your PS3 is Firmware v1.10 or less (we tested v1.31+, and it
appears plugged/fixed in them) then you should receive a BLACK
SCREEN... and if your Jumpdrive has a light it may also go out.

Next, power off your PS3 by pressing and holding the button.
You will receive a series of green LED blinks (about 25 total)
and around blink #19 you will also receive a series of audio
BEEPS as well.  Finally, your unit will shutdown to a red LED
and upon powering back on all will be back to normal.


Usage (tested on V1.11):

To use this, put the included "libmpeg.mpg" file in a /VIDEO
folder of your Jumpdrive or similar storage device.

Plug this device into your PS3 and load either a PS1, PS2, PS3,
or Bluray disk or a demo and then exit using the PS button.

Upon returning, go to Video, select your Jumpdrive, and select
the "Unsupported Data" file and launch it by pressing X.

If your PS3 is Firmware v1.11 or less (we tested v1.31+, and it
appears plugged/fixed in them) then you should receive a BLACK
SCREEN... and if your Jumpdrive has a light it may also go out.

Next, power off your PS3 by pressing and holding the button.  
You will receive a series of green LED blinks (about 25 total)
and around blink #19 you will also receive a series of audio
BEEPS as well.  Finally, your unit will shutdown to a red LED
and upon powering back on all will be back to normal.


The next step will be sorting how to inject code using this
method, followed by lovely PS3 homebrew and iSO Loaders of
course!

下载引导程序需要注册回复，不嫌麻烦的自己去下把，试过了的报告下啊

http://www.ps3ol.com/thread-6975-1-1.html.

Jeff_Chen

扯淡了吧，这个只是一个Exploit的实验而已。

跃动冲锋

不知道能不能用？

谁先尝螃蟹？

我随后

kaka1

下面是引用Jeff_Chen于2007-03-23 12:59发表的:
扯淡了吧，这个只是一个Exploit的实验而已。

国外已经有人通过这个程序成功引导了RR7.。。不相信没办法

永恒喜悦之泪

我1.6版本的破戒啥时出啊!!!

该用户已被禁言

有这个程序的人分享一下，不过我前两天已经从1.31升级到1.54，到昨天又升级到1.6了。。。。

zeroday

1.31版以后都不能用吧！

Jeff_Chen

下面是引用kaka1于2007-03-23 13:18发表的:


国外已经有人通过这个程序成功引导了RR7.。。不相信没办法

麻烦贴证据来，我只相信证据。你不懂英文我可以翻给你看。

kaka1

下面是引用Jeff_Chen于2007-03-23 13:31发表的:


麻烦贴证据来，我只相信证据。你不懂英文我可以翻给你看。

我还没试过，消息只是发来和大家分享的，你追求证据可以自己“实验”下就知道了。

gyfsgm

=.=根着消息实验，如果成砖冰！KAKA1赔机么。。。
不过话说我已经1。51了~过了刷机的可能鸟！