[破解]灵机一动！PS3已可运行D版PS2游戏(转至levelup.cn)

爱迪诗

PS3目前在全球市场上的销售明显弱于Wii和Xbox 360，不知大家有没有想过，这一定程度上和PS3是此代主机中唯一尚未被完全破解有关。当然，索尼自家拥有电影和唱片公司，并且是执行主机赔钱软件赚策略最坚决的厂商，因此绝对不希望PS3被破解。但玩家的信念是坚定的，最近在国外论坛上的一位仁兄就走出了一步。
   一位名叫pizzag的网友近日在网上写出了自己的小小改动过程。这一修改十分简单，只需要自制一个三相开关，并打开PS3的蓝光光驱，将开关的连线连接。这一修改实际上只是增加了第二种光盘弹出的途径。这样，只需要将一张正版PS2游戏插入，进入XMB界面后便已经通过了防盗版检查，这时用自制的开关将光盘弹出，再插入一张任何类型（刻录、盗版随意）的PS2光盘就可以进入游戏了。PS3在这期间不会发现你已经更换了光盘，而再次进行版权检查。
   由于没有蓝光刻录机，这位仁兄的下一步计划是找到一张可以刻录在DVD上的PS3游戏光盘，然后用正版PS3游戏来测试同样的方法。按理来说成功机率应当不小。如果这招真的奏效，那么索尼处心积虑炮制的严密防盗版措施被一个5美元买来的小开关打败，又是一个天大的笑话了。
      .

21克

如果是这样。蓝光影碟机的厂商要破产了.. ..

浪魂

转自:http://forums.afterdawn.com/thread_view.cfm/499497

PS3 Swap Switch Tutorial

OK, I wanted a fairly easy way to play my PS2 backups on my
PS3. I have read that you can do it by taking apart your PS3
and cutting a hole in the top and yadayada. Leaving the top
off of my PS3 to play PS2 backups didn't sound attractive to
me. So i searched around and found a forum for PS2 talking
about a tray switch for the fat PS2's back in the day. So i
did some brainstorming and figured it might work. I went to
Radio shack and purchased a 3 way toggle switch for $5. I
highly recommend 3 way. At radio shack it was called a middle
off switch. That way your drive motor is not constantly running.
I came home and soldered the wires to the switch.

A note before we start. This is a fairly easy process, the
most trouble i had was trying to figure out where to put the
switch. there is no room to work with. I ended up taking out
my card reader on my PS3 because i never use it and just mounted
the switch there. You could possibly let it hang out. It's up to
you. Just remember that if you plan to retain original
functionality as far as the drive sensor and automatic load/unload motor, you will need 2 additional small on/off switches.


The Switch I purchased:








1- Solder a wire from pin 6 to pin 1.






2- Solder a wire from pin 3 to pin 4.





3- Solder a RED wire to pin 4, and a BLACK wire to pin 1. This
will be your power wires that run to your Blu-ray load/unload
motor. I'd say make the length about a foot just to be safe. You
can cut off what you don't need later.





4- Pin 2 and pin 5 are the power source. Doesn't matter which
way you connect those. I'm using a plug-in power adapter with
an output switch on it up to 12 volts. It's set at 3 volts.








That's the hard part if you can believe it. Now you gotta bust
open the PS3. Very easy to do and no cutting or breaking involved.

1- Take the one bolt out on the side and slide the top off.

2- take the rest of the screws out and take the second top off.
This will expose the Blu-ray drive.




3- the Blu-ray drive has 2 plug-ins that need to be unplugged.
after that it comes out freely.

A- A ribbon on the bottom




B- A small plug-in on the left side




Note: Your main goal is to get to some small screws on the
bottom so that you can remove the metal cover. You may choose
not to unplug anything. That's up to you.

4- Take the metal top off. you will see a small circuit board
with 2 wires towards the front of the drive. This is a sensor
that allows the game to be sucked in. You need to disable this
by either cutting the small wires, Hooking up another small
switch so you still retain original functionality, or put a
small piece of tape over the sensor.




5- Unscrew the plastic top and take that off. This will allow
you to see much more of the drive on the inside.




6- The plastic piece I'm pointing to in the picture above needs
to come off. That will allow us to see the load/unload motor.
One small screw will allow you to remove this plastic part.




7- Once removed you will see the small motor which is what we're
after and makes this possible. You'll see 2 small wires soldered
onto the motor. RED and BLACK. You have another tough choice now,
if you chose to add a switch to the load sensor above, you will
need to add a switch to one of the original motor wires also.
This way, when you put your game in and the sensor sucks it in,
the motor will work automatically like it did to start with. If
you have the sensor turned on with a switch, you need the motor
turned on auto with a switch. that's where the 2 additional
switches come in if you choose to retain original functionality.
If you plan to load and unload games manually you only need
1 3-way switch and can disregard anything I've said about x-tra switches. The foot long wire you solder earlier to pins 4 and 1
now need to be soldered to the RED and BLACK terminals of your
motor. I just touched my soldering iron to the terminals and
removed the factory wires, tucked them away and soldered the
ones from my switch to it.







8- Now what i did was remove 3 small screws from a small circuit
board and ran my wires underneath it. Under the circuit board
there is a small hole that allows you to run the wire underneath
and out the bottom front of the Blu-ray drive. The board I'm
pointing to is the one that needs to be unscrewed. It doesn't
come off all the way but does enough for you to run wire under
it. When you put the screws back in make sure not to tighten
them down too much. just make them snug and make sure the small
switch on the right side of the board is in the proper place.




9- And that's pretty much it. Where you plan to mount the switch
or switches is up to you. the way i have mine set up is when the
switch is up the motor is sucking in. I start to put a game in
and it sucks it in. When the game is in and the drive engaged
i turn the switch to the middle position or off. turn on the
PS3 and the original game or Swap Magic will register with the
xmb. No need to actually boot the original game or swap magic
because as long as the game is recognized by the system, it has
passed any media checks. Next, I flip my switch down and the drive disengages and spits my game out. I then flip the switch back up
and insert my backup and turn the switch off. The whole time you
do the swap, the PS3 will still say you have a game inserted. So
if you choose to try this, you don't need anything special. 1-3 switches and an original PS2 game This is my first tutorial and
I'm sorry if it's bad. Feel free to redo it and repost it.
All i ask is that you don't try and take credit for what i've done. Other than that enjoy, be careful, and have fun.

PS: for my next trick i will get a PS3 backup that fits on a DVD
and insert my original Blu-ray PS3 game and then see if i can swap
it with a PS3 game on a DVD!!!
I have a 60gb U.S. PS3 running Firmware 1.51.

该用户已被禁言

MS这消息传得很广,到哪都能看到.

wzyzz

不知大家有没有想过，这一定程度上和PS3是此代主机中唯一尚未被完全破解有关。[/SIZE]这句话说的，买PS3首先是电视问题，等大多数人先把满高清电视拿下再说，当然有的人可以说我能将就，但至少我不会将就

yizhisun

好消息啊！距离破解不远了。

天霸绝枪

下面是引用yizhisun于2007-05-16 19:25发表的:
好消息啊！距离破解不远了。

坏消息,索尼随时可以升级系统软件

该用户已被禁言

谁试过???行不行呀?

tim_roger

赫赫  没办法  sony  太厉害了

chimae

如果一台播放器怎么容易就可以破解。你说这对它是好事还是坏事~~