- 精华
- 0
- 帖子
- 63
- 威望
- 0 点
- 积分
- 88 点
- 种子
- 0 点
- 注册时间
- 2006-8-18
- 最后登录
- 2010-10-28
|
Dark大神的TimeMachine 0.1{附下载} 转
Dark 时间机器翻译版！！！中文详解，附件下载，从此 pp不变砖！！！
看完了记得回一回哦!哪怕你只是回个表情!
TimeMachine 0.1
---------------
The Timemachine is a program to load previous firmwares and custom firmwares from memory stick
using pandora. Like devhook, but working throgh pandora and custom ipl's, it would work even if the
flash and nand ipl of the machine is destroyed.
The timemachine is useful to run software that is not supported anymore, and also as a way of
booting psp's even if the internal firmware is destroyed. It can also be useful for developers
to test their homebrew in different firmwares.
时间机器0.1版
时间机器是利用潘多拉电池从记忆棒里加载以前的官方系统或自制系统的程序。与DH类似，但是是以潘多拉电池和修改版的IPL为基础的，因此哪怕PSP的nand坏掉了，用时间机器仍然可以让PSP正常工作。
Currently the timemachine can install the following firmwares:
- Original 1.50 (can only be loaded on the phat)
- 1.50 with some 3.40 hw modules. Can be loaded on both, phat and slim.
- 3.40 OE (can only be loaded on phat)
- 3.60 M33 (can only be loaded on slim)
Rest of cfw will be added in the future.
目前时间机器可以安装下列系统：
- 原始1.5（只针对老P）
- 带有3.40固件模块的1.5，新P老P都适用
- 3.40OE（只针对老P）
- 3.60M33（只针对新P）
以后会添加更多系统支持
Requeriments of time machine:
- The timemachine itself doesn't require any firmware, only a pandora battery.
Timemachine nand boot in slim, requires, however, 3.90 M33-2 or greater.
- The timemachine installer requires 2.71 SE or higher.
时间机器的安装条件：
- 时间机器本身并不需要任何系统支持，仅仅需要潘多拉电池。新P需要3.90m33-2或更高才可以从nand启动。
- 时间机器的安装程序需要2.71SE或更高系统
Instructions: Copy the TIMEMACHINE folder to /PSP/GAME and run.
All firmwares can be installed on whatever PSP (slim or phat), but they can only be used
in the psp indicated in the option.
安装说明：把TIMEMACHINE文件夹复制到PSP/GAME里运行
新P和老P都能安装任意系统，但是只会在选项标明的psp上使用
Explanations of options:
- Option 1: Install iplloader. This will install the timemachine iplloader in the memory stick.
The iplloader is so small, that doesn't require any mspformat to have been done before.
This step is necessary to run anything else.
The iplloader of the timemachine is a multiipl loader that can load multiple ipl's accorrding
to key configurations found in the file /TM/config.txt (this file will be created by the timemachine installer).
安装选项说明：
- 选项1：安装IPL加载器，把时间机器的IPL加载器安装到记忆棒上。加载器很小，不需要对记忆棒进行mspformat格式化。
这一步对运行其他任何东西都是必须的。IPL加载器可以根据记忆棒里面ms0:/TM/config.txt对key的不同配置进行多重启动。（这个txt由时间机器安装程序自动生成）
The default configuration is to load the ipl's with the following keys:
- 1.50: cross
- 1.50+3.40hw: circle.
- 3.40 OE: triangle.
- 3.60 M33: square
- Pandora/DC1-4 ipl (converted to TM format): digital up
- Anything else: will boot the firmware installed on flash.
(Note: as said before, in the slim,
only nand firmwares with 3.90 M33-2 or higher can boot. Neither prvious CFW nor whatever original
firmware can boot from nand when booted from a Pandora battery due to a Sony protection that has to be bypassed by the own nand ipl code).
按不同的键加载不同的IPL
- 1.50：叉
- 1.50+3.40hw：圈
- 3.40 OE：三角
- 3.60 M33：方块
- 潘多拉电池1到4版的IPL（转换为TM格式）：方向键上
- 其他：启动PSP本身系统
（注意：如之前所说，新P必须是3.90m33-2或更高才可以从nand启动。之前的自制系统和任何官方系统因为sony的保护措施都不能从nand启动）
You can modify this configuration following the instructions of the file config_readme.txt that
will be written on the /TM folder after installing the iplloadder.
你可以根据config_readme.txt来修改设置，设置在安装IPL加载器后写入到TM文件夹里
- Option 2: Convert pandora IPL into TimeMachine format.
Because the ipl used in pandora and DC1-DC4 (they are all same) is not compatible with the
timemachine ipl format and user may want to load pandora/DC1-DC4 with the TM iplloader, this option
is for that.
Requeriments: the ipl of pandora/DC1-DC4 in the root of the memory stick, named "msipl.bin".
This file is written by Pandora and DC1-DC4 installers.
After convertion, the converted ipl will be in /TM/pandora.bin.
- 选项2：把潘多拉的IPL转换成时间机器格式
潘多拉系列的IPL和时间机器的不兼容，因此需要用TM IPL加载器来加载潘多拉系列的IPL。
要求：潘多拉系列的IPL文件放在记忆棒根目录，命名为msipl.bin，这个文件是做神奇记忆棒的时候写入的。转换完毕后的ipl文件是TM/pandora.bin
- Option 3: Install 1.50.
It will install 1.50 which can only be run on the psp phat (for a 1.50 that can be installed on
the slim go to the next section).
Requriments: the eboot.pbp of 1.50 in the root as 150.PBP
选项3：安装1.50
安装只有老P可以运行的1.5系统（新P想安装1.5系统看下个部分）
要求：1.5的官方固件命名为150.PBP放在记忆棒根目录
- Option 4: Install 1.50 with 3.40 HW modules. (PSP PHAT or SLIM).
This will install a mix of 1.50 software modules with some 3.40 hardware modules, so
it can work on the psp slim. It will usually run most 1.5 homebrew.
Requriments: 1.50 and 3.40 Sony eboot.pbp in the root renamed as 150.PBP and 340.PBP,
and the 360.PSAR on the root too (to know what the 360.PSAR is, read below, in the 3.60 M33 installation section).
- 选项4：安装带有3.40模块的1.5（新P老P均可）
安装1.5的软件模块和3.40的硬件模块的混合系统，新P也可以用，可以运行大部分1.5的自制程序。
要求：1.5和3.40的官方固件分别重命名为150.PBP和340.PBP，和360.PSAR一起放在记忆棒根目录，共三个文件。（不知道360.PSAR是什么的往下读，在3.60M33的安装部分）
From 1.50 it will be extracted most modules, usually the software related ones.
From 3.40, it will be extracted a few modules, usually hardware modules.
From 3.60, it will only be extracted the wlan bios of the slim chip.
从1.5的固件中提取大部分软件相关模块，从3.40固件中提取一些硬件模块，从3.60固件中提取新P芯片里的无线网络bios。
Known problems or considerations of the 1.50+3.40hw:
- The media doesn't work fine in the XMB (music, videos, etc).
Yeah, this is known, anyways the main purpose of this firmware is to run homebrew,
as for XMB usage is better to use a more modern one.
- The "videocodec bug", aka crappy pmf play, only happening in the slim.
For some hw incompatibilty that coudln't been resolved yet, pmf videos, including
the gameboot, will play crappily in the slim.
This will happen also in 1.5 games you try to run, videos will play crappily.
Because PMPAVC videos also use the videocodec API, they will play crappily too.
Normal pmp (xvid) (used on pimpstreamer too) will play fine however as they are decoded by cpu.
关于1.5和3.40混合系统的一些已知问题说明：
- XMB不可播放音频视频，毕竟安装混合系统主要是为了运行自制软件，如果用XMB的话还是用新系统的吧
- 新P播放pmf会卡，包括gameboot.pmf，目前这个问题还没有解决。
在一些1.5的游戏中这个问题同样存在。
因为PMPAVC也用了videocodec的编程接口，所以PMPAVC播放也会卡。但是xvid编码的pmp可以正常播放，因为是调用cpu解码而不是硬件解码。
- The exit with home with "odd colors" bug.
When exiting with home from a homebrew or game, you may see random colors at the end of the framebuffer.
Nothing important, it even gives it an accidental stylistic look :)
- The PC os may detect the PSP slim as a new device.
This is normal, psp slim has a different product id (pid), but 1.5 usb driver uses only the old phat
pid. Nothing important, the usb will work fine in the slim.
- Wlan. The wlan seems to be working, it has been tested using the network update download, and
pimpstreamer 201 for 1.50.
- 按HOME键退出会有诡异的颜色，不要惊慌。
- 新P连接电脑可能会被检测为新的USB设备。这是正常的，USB仍然可以正常使用。
However two things are recommended:
* Turn off the wlan power save.
* Use manual IP and DNS configuration (otherwise you may have DNS problems).
If you don't know the manual configuration for your router, just do an automatic connection
in a higher firmware, and write somewhere the data that appear in the test page at the end,
and use that info to fill the manual configuration in 1.50+3.40 hw.
* As in normal 1.50, there is no WPA support.
建议两件事：
* 在XMB中关闭wlan power save选项
* 使用手动IP和DNS设置（不然DNS会有问题），如果你不知道怎么手动设置，就在高系统版本下自动检测连接，然后把连接的参数记录下来在1.50和3.40混合系统里手动输入
* 在1.5里没有WPA支持
- Homebrew that uses some patching code over some of the module that are from 3.40,
will not work and will probably crash. This is obvious, they were coded to patch 1.50 modules :)
- 对3.40的一些模块使用补充代码的自制软件不能运行，这是必然的，因为本来是用来补充1.5模块的
- Option 5: Install 3.40 OE.
It will install original 3.40 OE which can only be booted on the phat.
Requeriments: 1.50 and 3.40 Sony eboot.pbp on the root as 150.PBP and 340.PBP
- 选项5：安装3.40 OE
安装原始的3.40OE系统，老P专用
要求：1.5和3.40的官方固件分别重命名为150.PBP和340.PBP放在记忆棒根目录
- Option 6: Install 3.60 M33.
It will install original 3.60 M33, that can only be run on slim.
Requeriments: 360.PSAR on the root.
Because there is no 3.60 eboot on the net as the slim was shipped directly with 3.60,
the 360.PSAR is a file that has to be created on a psp running 3.60 M33.
To dump 3.60: run the program 360DUMPER that is in this release in a psp running 3.60 M33.
The result 360.PSAR is a file that uses the decrypted psar format
(what a sce psar would look without encryption), that was already used in 3.51/3.52 M33, and
it will have following size and md5 (checked anyways by the tm installer):
Size: 18189502 bytes.
MD5: EAA13343C70D9B0337C75B295474C69A
- 选项6： 安装3.60 M33
安装3.60M33，新P专用
要求：360.PSAR放在记忆棒根目录
这是因为没有官方的3.6固件文件，最早的新P一出场就是3.60，所以360.PSAR需要从3.60M33里提取出来。
提取的方法：在3.60m33的PSP上运行360DUMPER
360.PSAR是使用解密psar格式的文件，根据下列文件大小和MD5自行验证文件完整性
Size: 18189502 bytes.
MD5: EAA13343C70D9B0337C75B295474C69A
本文转自tgbus的rockddr (豆子) ！！谢谢！！
[quote]临时文件下载：
TimeMachine 0.1.rar （提取码：f3292f02b7fb63453992f907a23dab38）
不能下载的用这个:
提取地点:http://pickup.mofile.com/3917823464342599提取码 3917823464342599
注意:那网络硬盘有问题!那些连接都点点试试看!. |
|
川公网安备 51019002005286号
楼主
发表于 2008-2-16 12:20 · 河北
