- 精华
- 0
- 帖子
- 571
- 威望
- 0 点
- 积分
- 686 点
- 种子
- 0 点
- 注册时间
- 2007-5-9
- 最后登录
- 2012-5-9
|
发表于 2008-7-4 14:55 · 未知
|
显示全部楼层
下面是引用woodbbb于2008-07-04 14:26发表的求助 39001 FMCB 后总是不能hdl 让放光盘:
我是用光盘里的uLaunchelf4.12启动
然后在mc里建立BOOT，把BOOT.ELF拉入（是提前在PC上改完名）
进入mass运行FMCB1.4B———— 格mc————安装————提示完毕自动关机
(DVDELF已准备好） 选的是DVDPLU 北美版 (尾数1,12) 我的机器是39001
在开机总是不能HDL，提示放入光盘
.......
# ----------------------------------------
# Free MCBoot Config File
# ----------------------------------------
#
# must be in mc?:/SYS-CONF/FREEMCB.CNF
#
# for boot from usb use for example : mass:/BOOT/BOOT.ELF
# for boot from memcard use for example : mc0:/BOOT/BOOT.ELF or mc1:/BOOT/BOOT.ELF
# you can use too for example : mc?:/BOOT/BOOT.ELF it wills check for the file in the two slots
#
# LK_???_E1 entries are first boot attempt, and LK_???_E2 entries are secondary boot file
#
# AutoBoot_Disc option allow to check if a disk is present (Close the tray !!!) and boot it, set it to 0 to avoid this.
# Debug_Screen set to 1 allow to keep the Green debug screen if no boot file is found, if set to 0 reject to browser
#
# You should not see Red screen if the CNF is readed, if you experience red screen check that you have config file in valid path
#
# All LK_???_E1 and LK_???_E2 entries can either be set to a path or to "OSDSYS", in the second case if no key is pressed you will be
# rejected to the browser. If you set a path it will be booted if no key pressed.
#
# ----------------------------------------
# Based on uLaunchELF
# ----------------------------------------
#
CNF_version = 1
#
# ----------------------------------------
#
LK_Auto_E1 = OSDSYS
LK_Auto_E2 =
LK_Circle_E1 =
LK_Circle_E2 =
LK_Cross_E1 =
LK_Cross_E2 =
LK_Square_E1 =
LK_Square_E2 =
LK_Triangle_E1 =
LK_Triangle_E2 =
LK_L1_E1 = mass:/BOOT/BOOT3.ELF
LK_L1_E2 = mc?:/BOOT/BOOT3.ELF
LK_R1_E1 = mass:/BOOT/BOOT1.ELF
LK_R1_E2 = mc?:/BOOT/BOOT1.ELF
LK_L2_E1 = mass:/BOOT/BOOT4.ELF
LK_L2_E2 = mc?:/BOOT/BOOT4.ELF
LK_R2_E1 = mass:/BOOT/BOOT2.ELF
LK_R2_E2 = mc?:/BOOT/BOOT2.ELF
LK_L3_E1 =
LK_L3_E2 =
LK_R3_E1 =
LK_R3_E2 =
LK_Up_E1 =
LK_Up_E2 =
LK_Down_E1 =
LK_Down_E2 =
LK_Left_E1 =
LK_Left_E2 =
LK_Right_E1 =
LK_Right_E2 =
LK_Start_E1 =
LK_Start_E2 =
LK_Select_E1 =
LK_Select_E2 =
AutoBoot_Disc = 1
Debug_Screen = 0
这个是1.4b的默认CNF。你看一下就知道为什么了。
根本就没有BOOT.ELF的相关连接。所以你把BOOT.ELF放到哪里都是无效的。
开机什么都不按默认进入OSDSYS，也就是7星。
为什么不用1.5。 1.5默认读BOOT.ELF。 |
|
川公网安备 51019002005286号
楼主
