- 精华
- 1
- 帖子
- 2086
- 威望
- 1 点
- 积分
- 2252 点
- 种子
- 0 点
- 注册时间
- 2005-10-9
- 最后登录
- 2013-6-23
|
楼主 |
发表于 2008-9-29 19:33 · 北京
|
显示全部楼层
1.5版本和1.6版本更新的内容
DosFlash and DosFlash32 V1.6 Beta
-----------------------------------
- fixed power brute unlock bug for VIA cards, this can stop your VIA from working
with the power brute unlocking in Version 1.5
- for DosFlash16 in auto mode on DOS my VIA card works best if I do a cold boot
and power up the drive short before or with the PC
- for DosFlash32 on Windows my VIA card works best if I power up the drive short
before starting DosFlash32
- for me the VIA works with internal and external connectors on DOS and Windows
Sorry for the trouble!
Kai Schtrom
************************************************************************************************
DosFlash and DosFlash32 V1.5 Beta
-----------------------------------
- now supports serial flash chip MT1309E with mediatek status 0x72 like the SH-D163B, SH-D162D,
Asus DVD-E616A3, Asus DVD-E818A3, Sony Optiarc DDU1671S
- SST25LF020A and SST25LF040A chip support added
- DosFlash32.exe ported from MFC to plain Windows API, exe size is now 22 KB
- new port i/o driver, because giveio.sys can't be compiled for 64 Bit Windows
- DosFlash16 changed slighly in manual mode, one parameter is added to support SST25LF020A and
SST25LF040A
- two new methods of BenQ soft unlock are now possible on all motherboards with only one power
supply unit
- 1st method is powered by Geremia's unlock core, thanks for the complete idea, concept and
source to Geremia
- 2nd method is the Magic28 key send, this only works on BenQ VAD6038 firmware, thanks to
c4eva and podger for the initial idea
- the two unlock methods are send one after the other if the drive is a possible unlock
candidate, first the Magic28 command, then Geremia's unlock commands and after that the
already known power brute unlock is send to the drive, you can cancel any of these methods
before they are send to the target, this only applies to BenQ drives with a locked flash
- DosFlash.typ updated
- other minor improvements
- DosFlash32 is now ready for
- Windows 2000
- Windows XP 32 Bit
- Windows XP 64 Bit
- Windows Server 2003 32 Bit
- Windows Server 2003 64 Bit
- Windows Vista 32 Bit
- Windows Vista 64 Bit
- Warning: Drivers for Windows Vista 64 Bit need to be signed, because we can't afford the
money to let portio64.sys sign you need to do the following:
1) Log on as Administrator
2) Enter the following command in a Dos-Box:
"bcdedit -set loadoptions DDISABLE_INTEGRITY_CHECKS"
(we made sure there are no typos in the line above) :)
3) Press enter and reboot your PC
4) Press F8 key upon initial system boot up
5) Choose to disable forced driver signing enforcement for that boot session
The following only applies to drives with a locked BenQ flash.
Geremia's BenQ unlock with DosFlash16 / DosFlash32 on any motherboard with the PC's psu
-----------------------------------------------------------------------------------------
- disable CD-ROM boot option in BIOS
- connect BenQ to your PC's power supply unit and SATA port
- power up PC, wait until bootup is finished
- eject tray of the BenQ and shutdown PC completely
- push the BenQ tray half in
- power up PC and boot into DOS for DosFlash16 or Windows for DosFlash32
- run DosFlash16 in auto mode for DOS or DosFlash32 for Windows
- if you read the following:
MTK Vendor Intro failed on port 0x????. Because there seems
to be a BenQ drive connected you should try Geremia's
unlock method.
- Eject drive tray
- Power off drive
- Push drive tray in until it is half open
- Power on drive
- Press "Yes" if you are ready
Are you ready (Y/N)?
- simply press 'Yes' without doing anything of the above, because we
already did that before starting DosFlash16 / DosFlash32
- the BenQ flash should now be identified
- go on like usual
Geremia's BenQ unlock with DosFlash16 / DosFlash32 on any motherboard with 2nd psu
------------------------------------------------------------------------------------
- connect a separate power supply unit to the BenQ, don't turn it on yet
- power up PC and boot into DOS
- run DosFlash16 in auto mode for DOS or DosFlash32 for Windows
- if you read the following:
MTK Vendor Intro failed on port 0x????. Because there seems
to be a BenQ drive connected you should try Geremia's
unlock method.
- Eject drive tray
- Power off drive
- Push drive tray in until it is half open
- Power on drive
- Press "Yes" if you are ready
Are you ready (Y/N)?
- do the above and press 'Yes'
- the BenQ flash should now be identified
- go on like usual
Magic28 BenQ unlock with DosFlash16 / DosFlash32 on any motherboard
---------------------------------------------------------------------
- connect BenQ to your PC's power supply unit and SATA port
- power up PC and boot into DOS for DosFlash16 or Windows for DosFlash32
- run DosFlash16 in auto mode for DOS or DosFlash32 for Windows
- if you read the following:
MTK Vendor Intro failed on port 0x????. Because there seems
to be a BenQ VAD6038 drive connected you should try the
Magic28 unlock method.
Do you want to send the Magic28 command?
- press 'Yes'
- the BenQ flash should now be identified
- go on like usual
Thanks to Redline99 and Tiros for help and support.
It's all about DOS!
Thanks guys for the excellent team work!
Geremia, Modfreakz and Kai Schtrom |
|
川公网安备 51019002005286号
发表于 2008-9-29 17:17 · 上海
